Invar Alloy

Original
price: Negotiable
minimum:
Total supply:
Delivery term: The date of payment from buyers deliver within days
seat: Beijing
Validity to: Long-term effective
Last update: 2017-12-21 16:29
Browse the number: 159
inquiry
Company Profile
 
 
Product details
Hangzhou Ualloy Material Co.,Ltd is one of the best invar alloy manufacturers and suppliers in China,Website:://.alloystrip.com, welcome to buy discount and low price invar alloy 4j36 wire, invar alloy 4j36 strip from us, and also welcome to check the price and quotation with our factory. FeNi(INVAR36) resistance alloy 1.Description Invar is an iron-nickel austenitic alloy of lowest thermal expansivity. It is strong, tough, ductile and possesses a useful degree of corrosion resistance, it is magnetic at temperatures below its Curie point and non-magnetic at temperatures above. Invar is therefore always magnetic in the temperature range in which it exhibits the low expansion characteristics. Invar is the standard alloy for low expansivity up to 400 oF. For applications at higher temperatures, the higher nickel alloys are recommended. INVAR36 Chemical Content(%) Ti Zr Mg Mn Si Cr Ni Al Fe P S 0.1 0.1 0.1 0.5 0.5 0.25 36.00 0.1 Bal. 0.02 0.02 Physical Properties(Annealed) Electrical Resistivity 494 ohms/mil/ft Density 0.292 lb/in Specific Gravity 8.08 Temperature Coefficient of Electrical Resistivity 0.67 x 10-3Degrees Fahrenheit Melting Point 1425 ℃ Curie Temperature 276℃ Inflection Temperature 190℃ Temperature Coefficient of Thermal Expansion -200 - 0 0F 0-200 0F 200-400 0F 400-600 0F 600-800 0F 800-1000 0F 1.1 0.7 1.5 6.4 8.6 9.5 Typical Hardness,Rockwell B Anealed Max 70 ¼ Hard 78 to 83 ½ Hard 84 to 88 Typical Tensile Strength(1000 psi) Anealed Max 85 ¼ Hard 90 to 115 ½ Hard 105 to 125 Hard Min120 2.Usage It is  widely used in molds for composite aircraft parts,molds for composite boat parts,precision condenser plates, resonant cavities for radars,precision measurements constructions,special joints and washers, thermostatic bimetals,laser part applications,clock pendulums,balance wheels,watch parts,tooling 3.Machinability Because of its high ductibility, the chips formed during machining tend to be stringy and tough, thus imposing rapid wear on cutting tool edges. In general, slow speeds and light feeds should be used to avoid excessive heat and minimize the possibility of the generated heat affecting the expansion characteristics. The use of soluble oil cutting compound is recommended for all machining operations. 4.Workability Forging: The principal precaution to observe in forging is to heat quickly and avoid soaking in the furnace. Long soaking may result in a checked surface due to absorption of sulfur from the furnace atmosphere and/or oxide penetration. Blanking and Forming: Alloy 36 presents no unusual problems in blanking and forming. For cleanest blanking properties, a Rockwell hardness of B90 is suggested. This hardness will allow mild bending and forming operations. Where deep drawing operations are involved a finish annealed strip of a Rockwell harness of about B75 is usually desirable. Grinding: A silicon carbide wheel is desirable, preferably a soft wheel which will wear without loading. Welding: Alloy 36 can be welded by the conventional methods. Caution must be taken so as not to overheat the molten metal. This will avoid spattering of the molten metal and pits in the welded area. When welding with rod, it is essential that the rod be of the same composition if similar properties in the weld are desired.The rods should be heavily coated. In oxyacetylene welding, the flame is maintained slightly on the reducing side. Brazing: Silver and zinc-free alloys have been used for brazing Invar 36. This alloy should be annealed prior to brazing. Joints should be designed to avoid placing material in tension during brazing. If silver soldering is done manually, the parts should be preheated to 800 oF and slowly cooled. Plating: Alloy 36 can be chromium, cadmium and nickel plated or zinc coated by the usual methods used for ferrous alloys. Pickling: Pickling is best done in hydrochloric acid solutions. A 25% solution at 160 oF is particularly effective. Distortion:Invar has poor heat conductivity, a low coefficient of expansion at temperatures below 300 oC, normal coefficient of expansion at higher temperatures, and an elastic modulus 79% of steel. These conditions promote internal strain and distortion. Note carefully the section on stress relief. We suggest a rapid air cool instead of a water quench whenever possible.
Total0bar [View All]  Related Comments
 
more»Other products

[ Products search ] [ favorites ] [ Tell friends ] [ Print ] [ Close ]